Support & Videos

Safety Advice

SAFETY NOTICE ENDCAP PIN 
How to replace your short endcap pins.
We have 
identified irregularities in the manufacturing of some CORE Sensor 3 and 3S Bars. Specifically, there are instances of insufficient length of the endcap pinsIf your check shows that you need to change your pins, here's how to do it. Iis straightforward and takes only a few minutes. Open the Stealth Winder, press out the insert labeled "Press," use the new pin to replace the old one, and reposition the insert, ensuring it clicks securely into place. 
SAFETY NOTICE: QR + SAFETY LINE
Safety notice regarding care and maintenance of the Sensor 2S bar
 
Ensure all safety mechanisms including the safety line and the tube it travels through are free of sand and fully functional before every launch.Rinse your Sensor 2S bar with fresh water after every use. While rinsing, release the chickenloop and feed the safety line back and forth through the stainless steel tube to remove any potential debris. Inspect the Rotor quick release, safety line movement, and ceramic bearings and clean if required.
Sicherheitshinweise QR + Safety Line

SENSOR 3 Bar Systems

Full Bar REPLACEMENt 

How to replace your control bar.
Sensor 3, Sensor 3 Pro

bar insert Replacement

How to replace your bar inserts.
Sensor 3, Sensor 3 Pro
 

Bar Width adjustment

How to change your bar width on your Sensor Sensor 3, Sensor 3 Pro
 

frontline REPLACEMENt 

How to replace a frontline.
Sensor 3, Sensor 3 Pro

floater bungee handle REPLACEMENt

How to exchange the floater bungee handle
Sensor 3, Sensor 3 Pro
 

endcap insert Replacement

How to exchange the endcap inserts.
Sensor 3, Sensor 3 Pro
 

connector set REPLACEMENt 

How to exchange the connector set.
Sensor 3, Sensor 3 Pro

bar leader line REPLACEMENt

How to exchange the bar leader line.
Sensor 3, Sensor 3 Pro
 

Power Line REPLACEMENT 

How to replace the power line. 
Sensor 3, Sensor 3 Pro.
 

Safety and Power line REPLACEMENt

How to replace the power & safety line.
Sensor 3, Sensor 3 Pro

CHICKEN Loop REPLACEMENt

How to replace the chicken loop.
Sensor 3, Sensor 3 Pro
 

Power Line REPLACEMENT 

How to replace the power line. 
Sensor 3, Sensor 3 Pro.
 

CHICKEN Loop REPLACEMENt

How to replace the chicken loop.
Sensor 3, Sensor 3 Pro
 

SFF-Rope / Powerline Replacement

How to replace SSF-Rope and Powerline.
Sensor 3, Sensor 3 Pro
 

SENSOR 2 Bar Systems

line length check and adjustment 

How to check and adjust line length on a Sensor bar.
Sensor 2, Sensor Pro, Sensor 2S/2S+, Sensor 2S Pro

CHICKEN Loop REPLACEMENt

How to replace the chicken loop.
Sensor 2, Sensor Pro, Sensor 2S/2S+, Sensor 2S Pro

Chicken Stick REPLACEMENT 

How to replace the chicken stick.
Sensor 2, Sensor Pro, Sensor 2S/2S+, Sensor 2S Pro

Depower Line Replacement

How to replace the depower line.
Sensor 2S/2S+, Sensor 2S Pro

Line-Inserts REPLACEMENt

How to replace the bar line-inserts.
Sensor 2S/2S+, Sensor 2S Pro
 

Safety Line REPLACEMENT 

How to replace the safety line.
Sensor 2S/2S+, Sensor 2S Pro

Wakestyle Set Installation

How to install the wakestyle set.
Sensor 2S/2S+, Sensor 2S Pro
 

Safety line replacement

How to replace the safety line.
Sensor 2, Sensor Pro

Depower line REPLACEMENT 

How to replace the depower line.
Sensor 2, Sensor Pro

Pro Leash 1.0 set up and release

How to put the Pro Leash 1.0 together and release it.

bar width change

How to change the Sensor bar width.
Sensor 2, Sensor Pro, Sensor 2S/2S+, Sensor 2S Pro

IMPACT'S 5TH LINE CONNECTION

How to connect the Impact's 5th line.
Sensor 2, Sensor Pro, Sensor 2S/2S+, Sensor 2S Pro
 

Kite BLADDER REPLACEMENT

Bladder-Bezeichnung
BLADDER

All leading edge and strut bladders are available as single parts.

STRUT BLADDER REPLACEMENT

Section 1: Chris shows how to remove a fast pump strut bladder and how to put in again.

LEADING EDGE BLADDER REPAIR

Section 2: Chris Bösch demonstrates the repair procedure of the inflatable leading edge.

BLADDER REPAIR

Section 3: Chris shows how to find the air leak and the detailed procedure of a bladder repair. He is using the always included Repair Kit Pro.

RED SPEED PUMP VALVE REPLACEMENT

Section 4: Chris shows how to replace the red speed pump valve on a strut bladder. This is kind of similar on all other CORE kites.



 

You didn't find what you were looking for?


Check our knowledge base to find an answer.

Send us a message or call us on +49 4371 88934-0 and we're happy to help you out!